TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE..
m Vehicle Theft Alarm — If Equipped ...27m Sliding Side Door ...28▫ Power Sliding Door — If Equipped ...30▫ Child P
3. Additional Storage—The 2nd row seats are installed in the middle seatingposition. Either or both of the rear seats are removedfrom the vehicle.4. A
WARNING!• Not all head restraints in this vehicle are the same.Head restraints from one seating position should notbe removed and installed in any oth
Your vehicle may have been delivered with two RemoteKeyless Entry transmitters. One or both transmitters canbe linked to either memory position. The m
9. Press and release the LOCK button on one of thetransmitters.Achime will soundsignaling to youthat thetransmitter has been successfully linked to me
To Disable A Transmitter Linked to Memory1. Turn the ignition switch to the OFF position andremove the key.2. Press and release memory button number 1
TO OPEN AND CLOSE THE HOODTo open the hood, two latches must be released. First pullthe hood release lever located under the left side of theinstrumen
WARNING!If the hood is not fully latched, it could fly up whenthe vehicle is moving and block your forward vision.You could have a collision. Be sure
by pressing the lens. The lights will remain on until thelens is pressed a second time, so be sure they have beenturned off before leaving the vehicle
Dome Light PositionRotate the dimmer control com-pletely upward to the second de-tent (extreme top position) to turnon the interior lights, except the
ON for up to 90 seconds after you turn the ignitionswitch OFF. To turn the Automatic System OFF, turn theheadlight switch clockwise to the OFF positio
m Safety Tips ...73▫ Exhaust Gas ...73▫ Safety Checks You Should Make Inside TheVehicle ...
headlights within 45 seconds. The 90 second delay inter-val begins when headlight switch is turned off. If theheadlights or park lights are turned bac
Turn Signal WarningIf the vehicle electronics sense that the vehicle hastraveled at over 18 mph (29 km/h) for about one milewith the turn signals on,
NOTE: Always remove any build-up of snow thatprevents the windshield wiper blades from returning tothe OFF position. If the windshield wiper switch is
WARNING!Sudden loss of visibility through the windshieldcould lead to an accident. You might not see othervehicles or other obstacles. To avoid sudden
TILT STEERING COLUMN — IF EQUIPPEDTo tilt the column, pull the small lever, located behind theturn signal control, toward you and move the wheel upor
TRACTION CONTROL SWITCH — IF EQUIPPEDThe TRAC indicator, located below the instrument clusterodometer, will lightup whenthe Traction Control isin use.
ADJUSTABLE PEDALS — IF EQUIPPEDThis feature allows both the brake and accelerator pedalsto move toward or away from the driver to provideimproved posi
•The pedals cannot be adjusted when the vehicle is in R(Reverse) or when the Speed Control System is ON.The following messages will be displayed on ve
To Activate:Push the “ON/OFF” button once and the CRUISE indi-cator located below the instrument cluster odometer willilluminate showing the electroni
To Vary the Speed Setting:When the speed control is set, speed can be increased bypressing and holding the “RESUME/ACCEL” button.When the button is re
A WORD ABOUT YOUR KEYSYou can insert the double sided keys into the locks witheither side up.The dealer that sold you your new vehicle has the keycode
WARNING!Speed Control can be dangerous where the systemcan’t maintain a constant speed. Your vehicle couldgo too fast for the conditions, and you coul
The lights also turn on when a front door, a sliding dooror the liftgate is opened. If your vehicle is equipped withRemote Keyless Entry, the lights w
turns in an area free from large metal or metallic objects,the “CAL” symbol will turn off and the compass willfunction normally.Manual Compass Calibra
To set the variance: Turn the ignition switch ON and setthe display to Comp/Temp. On vehicles equipped with aCompass/Mini Trip Computer press the RESE
Mini-Trip ComputerThis displays information on the following:•Average Fuel Economy (ECO AVG)Shows the average fuel economy since the last reset.•Dista
Electronic Vehicle Information Center (EVIC) — IfEquippedThe Electronic Vehicle Information Center, when theappropriate conditions exist, displays the
NOTE: Tire pressure menu items are available only onvehicles equipped with the Tire Pressure Monitor Sys-tem.Customer Programmable Features — If Equip
the Tire Pressure Monitor system and the training routineis not performed, training will be cancelled after oneminute or the next time you cycle the i
Remote Linked To Memory (Available withMemory Seat and Pedals Only)When this feature is selected, pressing the Unlock buttonon any Remote Keyless Entr
Headlamp DelayWhen this feature is selected the driver can choose, whenexiting the vehicle, to have the headlamps remain on for30, 60, or 90 seconds,
NOTE: The power window switches, radio, poweroutlets, and removable console (if equipped), will remainactive for up to 45 seconds after the ignition s
WARNING!A moving garage door can cause injury to people andpets in the path of the door. People or pets could beseriously or fatally injured. Only use
WARNING!Vehicle exhaust contains carbon monoxide, a danger-ous gas. Do not run the vehicle’s exhaust whiletraining the transceiver. Exhaust gas can ca
NOTE: Some gate operators and garage door openersmay require you to replace this Programming Step 3 withprocedures noted in the 9Gate Operator/Canadia
and, depending on the brand of the garage door opener(or other rolling code equipped device), repeat thissequence a third time to complete the program
etc.). For convenience, the hand-held transmitter of thedevice may also be used at any time. In the event thatthere are still programming difficulties
This device complies with part 15 of FCC rules and withRSS-210 of Industry Canada. Operation is subject to thefollowing conditions:•This device may no
switch rearward will activate the Express Open Feature,causing the sunroof to open automatically.Press and hold the button located to the right of the
WARNING!In an accident, there is a greater risk of being thrownfrom a vehicle with an open sunroof. You could alsobe seriously injured or killed. Alwa
ELECTRICAL POWER OUTLETS — IF EQUIPPEDTo the left of the instrument panel cup holder are two 12volt power outlets. The upper outlet is controlled by t
The lower outlet is protected by an automatic reset circuitbreaker. The automatic circuit breaker restores powerwhen the overload is removed. The circ
chip (transponder) embedded into them. Only keys thathave been programmedto the vehicle can beused to startand operate the vehicle.The Sentry Key Immo
CONVENIENCE TRAY DRAWER AND CUPHOLDERSInstrument Panel Cup HoldersThe instrumentpanel cupholders are located in a pull outdrawer just below the climat
With the optional dealer installed Smoker’s package, aremovable ash receiver is inserted into the conveniencetray location. To install the ash receive
•The quad seat cupholders are designed to break awayif stepped on. To return the cupholder to its normalposition, simply push the cupholder up to snap
breaker and is powered directly from the battery, itemsplugged into this outlet may discharge the batteryand/or prevent engine starting.To remove the
To reinstall the console, remove the rubber mat andrelocate to the alternate floor tray, slide the consoleforward to engage the front of the console i
CAUTION!•Many accessories that can be plugged in drawpower from the vehicle’s battery, even when notin use (i.e. cellular phones, etc.). Eventually, i
The liftgate sill plate has a raised line with the statement“Load To This Line”. Thisline indicates how farrearwardcargo can be placed without interfe
1. To raise the cargo organizer pull up on the handle andpull towards the rear of the vehicle.2. Place the rear corners of the cargo organizer into th
CAUTION!Do not load objects over 100 lbs (45 kg) in the lowerposition. Failure to follow this could cause damageto the cargo organizer.To Open Storage
Cargo Organizer removalUnscrew the two plastic fasteners located on the floor ofthe rear of the cargo area and remove the cargo organizerfrom the vehi
All of the keys provided with your new vehicle havebeen programmed to the vehicle electronics.Replacement KeysNOTE: Only keys that have been programme
capacity of the vehicle. Be sure the total load of cargoinside the vehicle plus that on the external rack does notexceed the maximum vehicle load capa
CAUTION!•To avoid damage to the roof rack and vehicle, donot exceed the maximum roof rack load capacityof 150 lbs (68 kg). Always distribute heavy loa
LOAD LEVELING SYSTEMThe automatic load leveling system will provide a levelriding vehicle under most passenger and cargo loadingconditions.A hydraulic
UNDERSTANDING YOUR INSTRUMENT PANELCONTENTSm Instruments And Controls ...158m Instrument Cluster With Tach ...159m Premium In
▫ Power Switch, Volume Control ...171▫ Seek Button (Radio Mode) ...171▫ Tuning ...171▫ PTY (Program Typ
▫ Program Button 4 (Random Play) ...178▫ Mode ...179▫ Tape CD Button ...179▫ Time Button ...
▫ Time Button ...197▫ Changing Modes ...197▫ Removing Discs From The CD Changer ...197▫CD Changer Operation
▫ Infrared Three-Zone Automatic TemperatureControl — If Equipped ...219m Rear Window Features ...230▫ Intermittent Rear
INSTRUMENTS AND CONTROLS158 UNDERSTANDING YOUR INSTRUMENT PANEL
INSTRUMENT CLUSTER WITH TACHUNDERSTANDING YOUR INSTRUMENT PANEL 1594
4. Insert a blank Sentry Key into the ignition switch andturn the ignition switch ON within 60 seconds. After 10seconds asingle chime willsound. The T
PREMIUM INSTRUMENT CLUSTER160 UNDERSTANDING YOUR INSTRUMENT PANEL
INSTRUMENT CLUSTER DESCRIPTIONS1. Fuel GaugeThe pointer shows the level of fuel in the fuel tank whenthe ignition switch is in the ON position.2. Low
NOTE: The light may flash momentarily during sharpcornering maneuvers which change fluid level condi-tions. The vehicle should have service performed.
8. Anti-Lock LightThis light monitors the Anti-Lock Brake System.The light will turn on when the ignition switch isturned to the ON position and may s
12. Engine Temperature Warning LightThis light warns of an overheated engine condi-tion. If the engine is critically hot, a continuouschime will sound
WARNING!A hot engine cooling system is dangerous. You orothers could be badly burned by steam or boilingcoolant. You may want to call a service center
engine start. The vehicle should be serviced if the lightstays on through several of your typical driving cycles. Inmost situations the vehicle will d
20. Odometer/Trip OdometerThe odometer shows the total distance the vehicle hasbeen driven.U.S. federal regulations require that upon transfer ofvehic
When the tire pressure monitoring system warning lightis lit, one or more of your tires is significantly underin-flated. You should stop and check you
will sound to alert you to turn the signals off. If eitherindicator flashes at a rapid rate, check for a defectiveoutside light bulb.High Beam LightTh
NOTE:•The front courtesy overhead console, door courtesyand liftgate lights do not turn on if the dimmer controlis in the interior lights ON position
Two Types of SignalsThere are two basic types of radio signals... AM orAmplitude Modulation, in which the transmitted soundcauses the amplitude, or he
SALES CODE RAZ—AM/ FM STEREO RADIOWITH CASSETTE TAPE PLAYER, CD PLAYERAND CD CHANGER CONTROLS — IF EQUIPPEDOperating Instructions — RadioNOTE: Power t
PTY (Program Type) ButtonPressing this button once will turn on the PTY mode for5 seconds. If no action is taken during the 5 second timeout the PTY i
By pressing the SEEK button when the PTY icon isdisplayed, the radio will be tuned to the next frequencystation with the same selected PTY name. The P
AM/FM SelectionPress the AM/FM button to change from AM to FM. Theoperating mode will be displayed next to the stationfrequency. The display will show
To Change From Clock To Radio ModePress the Time button to change the display betweenradio frequency and time.Operating Instructions — Tape PlayerInse
Tape EjectPress the EJT Tape button and the cassette will disengageand eject from the radio.Scan ButtonPress this button to play 10 seconds of each se
Operating Instructions — CD PlayerNOTE: The ignition switch must be in the ON or ACCposition andthe volume controlON before the CD playerwill operate.
Seek ButtonPress the top of the SEEK button for the next selection onthe CD. Press the bottom of the button to return to thebeginning of the current s
MODEPress the MODE button to select between the tape player,CD player, or satellite radio (if equipped).To select Satellite Radio (if equipped), press
WARNING!•For personal security and safety in the event of anaccident, lock the vehicle doors as you drive aswell as when you park and leave the vehicl
Push-ButtonWhile the CD changer is playing, press the NUMBER 1push-button or the NUMBER 5 push-button to select adisc numbered higher or lower than th
•Damaged disc•Water condensation on opticsSALES CODE RBQ—AM/FM STEREO RADIOWITH 6 - DISC CD CHANGERRadio OperationPower/Volume ControlPress the PWR/VO
channel number will then be displayed for five seconds.The current channel name and number will then bedisplayed until an action occurs. CD’s may rema
“1–6” button you wish to lock onto this station and pressand release that button. If a button is not selected within5 seconds after pressing the SET R
Inserting The Compact DiscCAUTION!This CD player will accept 43⁄4inch (12 cm) discsonly. The use of other sized discs may damage theCD player mechanis
If you have ejected a disc and have not removed it within15 seconds, it will be reloaded. If the CD is not removed,the radio will continue to play the
PTY (Program Type) ButtonPressing this button once will turn on the PTY mode for5 seconds. If no action is taken during the 5 second timeout the PTY i
Program Type Radio DisplayTalk TalkTop 40 Top 40Weather WeatherBy pressing the SEEK button when the PTY icon isdisplayed, the radio will be tuned to t
SALES CODE RBK—AM/ FM STEREO RADIOWITH CD PLAYER AND CD CHANGERCONTROLSRadio OperationPower/Volume ControlPress the ON/VOL control to turn the radio o
TunePress the TUNE control up or down to increase ordecrease the frequency. If you press and hold the button,the radio will continue to tune until you
If you press the power door lock switch while the slidingdoor is open, the sliding door will lock.Automatic Door Locks — If EquippedThe doors will loc
You may add a second station to each push-button byrepeating the above procedure with this exception: Pressthe SET button twice and SET 2 will show in
CD Player OperationNOTE: The ignition switch must be in the ON or ACCposition andthe volume controlON before the CD playerwill operate.Inserting The C
FF/TUNE/RWPress FF (Fast Forward) and the CD player will begin tofast forward until FF is released. The RW ( Reverse)button works in a similar manner.
Push-ButtonWhile the CD changer is playing, press the NUMBER 1push-button or the NUMBER 5 push-button to select adisc numbered higher or lower than th
An ERR symbol will appear on the display if the laser isunable to read the Disc data for the following reasons:•Excessive vibration•Disc inserted upsi
6 DISC CD CHANGER — IF EQUIPPEDThe CD changer is located below the radio in theinstrument panel. The changer plays only 43⁄4inch (12cm) discs. The cha
Playing DiscsThe radio will show the CD number, the CD tracknumber, and the Track Time Elapsed while the radio is inthe CD mode. If more than one CD i
Program Button 5Press this button to play the previous disc.Time ButtonPress this button to switch between time of day and CDtrack time.Changing Modes
changing tracks or DVD functions, as well as selectingdiscs loaded in the 6 disc CD/DVD changer whilelistening to the Rear Audio/Video System.Operatin
4. Repeat the process for loading any additional CD/DVDs. The CD/DVD changer will stop while additionalCD/DVDs are loaded.If the volume control is ON,
4. any door is opened (excluding liftgate) and5. the vehicle speed is 0 mph (0 km/h).The Auto Unlock feature can be enabled or disabled byperforming t
Operating Instructions — Remote ControlPower Button (PWR)Pressing the “POWER” button will turn the rear audio/video system ON/OFF. The headphone symbo
SEEK Button•CD/DVD changerPress the right side of the “SEEK” button for the nextchapter or track on the disc. Press the left side to return tothe begi
Operating Instructions — Video ScreenPush up on the release button to lower the video screen.1. Screen Width ButtonChanges the width of the screen pic
Operating Instructions — Headphones1. ON/OFF Button2. Scan Button3. Volume Control4. LEDPower ButtonPressing the power button will turn the headphones
headphones are on. This button is used only if theheadphones are locked on to a source other than thevehicle’s radio.NOTE: When the “GREEN LED” is sho
General InformationThis device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing two conditio
REMOTE SOUND SYSTEM CONTROLS — IFEQUIPPEDThe remote sound system controls are located on the rearsurface of the steering wheel at the 3 and 9 O’clockp
Tape PlayerPressing the top of the switch once will go to the nextselection on the cassette. Pressing the bottom of theswitch once will go to the begi
5. Aloose tape should be corrected before use. To rewinda loose tape, insert the eraser end of a pencil into the tapedrive gear and twist the pencil i
RADIO OPERATION AND CELLULAR PHONESUnder certain conditions, the cellular phone being On inyour vehicle can cause erratic or noisy performance fromyou
Six button transmitters will provide functions that allowthe same basic operation asthethree button,butmayalsobe used to Open/Close the optional power
other than off, it selects the amount of air delivered to thepassenger compartment. There are four blower speeds.The fan speed increases as youmove th
Front Mode ControlThe mode control allows you tochoose from several patterns ofairdistribution.NOTE: To improve your selection choices, the systemallo
Bi-Level ModeAir comes from both the instrument panel outlets, flooroutlets and defrost.Aslight amount of air is also directedthrough the side window
Mix ModeAir comes from the floor, defrost and side windowdemist outlets. This mode works best in cold or snowyconditions. It allows you to stay comfor
Defrost modes are selected. This is done to assist indrying the air and it will help in keeping the windowsfrom fogging.Manual Air Conditioning Operat
recirculation mode to rapidly cool the inside of thevehicle. The recirculation mode can also be used totemporarily block out outside odors, smoke, and
•Start the engine, and continue to hold in the “RearWipe/Wash” button until the indicator light startsflashing repeatedly.•Press the recirculation but
Rear Blower ControlThe primary control for the rear blower is on the frontclimate control unit located on the instrument panel.The center knob on the
CAUTION!Interior air enters the Manual Rear Zone ClimateControl system through an intake grille located inthe passenger side trim panel behind the thi
Infrared Three-Zone Automatic TemperatureControl — If EquippedThe Infrared Three-ZoneAutomatic Temperature ControlSystem automaticallymaintains the in
To unlock the doors and liftgate:Press and release the UNLOCK button on the transmitteronce to unlock the driver’s door side of the vehicle, ortwice t
desired temperature is displayed, the system will achieveand maintain that comfort level automatically. When thesystem is set up for your comfort leve
•The “DELAY” symbol will flash to indicate that thefeature as been enabled.Power ButtonThis button turns the entire system ON/OFF. When thesystem is t
Bi-Level ModeAir comes from both the instrument panel outlets, flooroutlets and defrost.Aslight amount of air is also directedthrough the side window
Mix ModeAir comes from the floor, defrost and side windowdemist outlets. This mode works best in cold or snowyconditions. It allows you to stay comfor
Depress the “A/C” button to turn on and off theair conditioning during manual operation only.Cool dehumidified air comes through the outletsselected b
Selecting the “AUTO” position for the Rear AutomaticTemperature Control System from the front ATC controlunit, illuminates a “LOCK” symbol in the rear
Rear Temperature Control button. Once the desired tem-perature is displayed, the system will achieve and main-tain that comfort level automatically. W
CAUTION!Interior air enters the Rear Automatic TemperatureControl System through an intake grille located inthe passenger side trim panel behind the t
Bi-Level ModeAir comes from both the headliner outlets and thefloor outlets.NOTE: In many temperature positions, the bi-levelmode is designed to provi
Window FoggingVehicle windows tend to fog on the inside in mild rainyor humid weather. To clear the windows, use the A/C,PANEL and blower controls. Di
headlights and park lights will flash, the horn will pulseon and off and the interior lights will turn on.The panic alarm will stay on for 3 minutes u
A/C Air Filter — If EquippedThe climate control system filters out dust, pollen andsome odors from the air. Strong odors can not be totallyfiltered ou
Rear Wiper Operation — Automatic TemperatureControl OnlyPress this button to have the rear wiper have acontinuous wipe. When the ignitionswitch isin t
NOTE: The washers will stop spraying if the switch ispressed longer than 10 seconds.Adding Washer FluidThe fluid reservoir for the windshield washers
Electric Rear Window Defroster — If EquippedPress this button to turn on the rear windowdefroster and the optional heated mirrors. A lightwill showtha
STARTING AND OPERATINGCONTENTSm Starting Procedures ...238▫ Normal Starting ...238▫ Extremely Cold Weather(Below
m Tire Safety Information ...252▫ Tire Markings ...252▫ Tire Identification Number (TIN) ...255▫ Tire Load
m Tire Rotation Recommendations ...273m Fuel Requirements ...274▫ Reformulated Gasoline ...275▫ Gasoline/Oxy
STARTING PROCEDURESCAUTION!Long periods of engine idling, especially at highengine speeds, can cause excessive exhaust tempera-tures which can damage
WARNING!Do not attempt to push or tow your vehicle to get itstarted. Vehicles equipped with an automatic trans-mission cannot be started this way. Unb
To Open/Close Right Power Sliding Door — IfEquippedPress the RIGHT button twice within five seconds toopen/close the right power sliding door. If the
CAUTION!To prevent damage to the starter, do not crank theengine for more than 15 seconds at a time. Wait 10 to15 seconds before trying again.If the e
AUTOMATIC TRANSMISSIONCAUTION!Damage to the transmission may occur if the follow-ing precautions are not observed:•Shift into PARK only after the vehi
Automatic Transmission Ignition Interlock SystemThis system prevents the key from being removed unlessthe shift lever is in PARK. It also prevents shi
possible convenience. Your dealer has diagnostic equip-ment to determine if the problem could recur.If the transmission cannot be reset, dealer servic
•“3” DriveThis range eliminates shiftsinto Overdrive. Thetransmis-sion will operate normally in First, Second and Thirdwhile in this range. The “3” po
CAUTION!All wheels must have the same size and type tires.Unequal tire sizes must not be used. Unequal tiresize may cause failure of the power transfe
added precaution, turn the front wheels toward the curbon a downhill grade and away from the curb on a uphillgrade.The parking brake should always be
by increased pedal travel during application, greaterpedal force required to slow or stop, and potentialactivation of the Brake Warning Lamp.Anti-Lock
When the vehicle is driven over approximately 15 mph(25 km/h), you may also hear a slight clicking sound aswell as some related motor noises. These no
WARNING!•Anti-lock system (ABS) cannot prevent the natu-ral laws of physics from acting on the vehicle, norcan it increase braking or steering efficie
General InformationThis device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•
WARNING!Continued operation with reduced power steeringassist could pose a safety risk to yourself and others.Service should be obtained as soon as po
•There is a Traction Control System malfunction•The system has been deactivated to prevent damage tothe brake system due to overheated brake tempera-t
TIRE SAFETY INFORMATIONTire MarkingsNOTE:•P(Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” moldedi
Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standards(...blank...( = Passenger car tire based on Euro
EXAMPLE:Service Description:95 = Load Index—A numerical code associated with the maximum load a tire can carry.H = Speed Symbol—A symbol indicating th
Tire Identification Number (TIN)The TIN may be found on one or both sides of the tirehowever the date code may only be on one side. Tireswith white si
Tire Loading and Tire PressureTire Placard LocationNOTE: Some vehicles have a “Tire and Loading Infor-mation” placard located on the driver’s side “B”
LoadingThe vehicle maximum load on the tire must not exceedthe load carrying capacity of the tire on your vehicle. Youwill not exceed the tire’s load
5. Determine the combined weight of luggage and cargobeing loaded on the vehicle. That weight may not safelyexceed the available cargo and luggage loa
STARTING AND OPERATING 2595
Transmitter Battery ServiceThe recommended replacement battery is one CR2032battery.NOTE: Do not touch the battery terminals that are onthe back housi
WARNING!Overloading of your tire is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use tir
2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread
The pressure should be checked and adjusted as well asinspecting for signs of tire wear or visible damage at leastonce a month. Use a good quality poc
Tire pressure may increase from 2 to 6 psi (13 to 40 kPa)during operation. DO NOT reduce this normal pressurebuild up or your tire pressure will be to
Radial-Ply TiresWARNING!Combining radial ply tires with other types of tireson your vehicle will cause your vehicle to handlepoorly. The instability c
Do not install a wheel cover or attempt to mount aconventional tire on the compact spare wheel, since thewheel is designed specifically for the compac
Tread Wear IndicatorsTread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced.These indic
WARNING!• Do not use a tire, wheel size or rating other than thatspecified for your vehicle. Some combinations ofunapproved tires and wheels may chang
Improper alignment will not cause vehicle vibration.Vibration may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration
are significantly underinflated. It is particularly impor-tant, therefore, for you to check the tire pressure in all ofyour tires regularly and mainta
VEHICLE THEFT ALARM — IF EQUIPPEDThis system monitors the vehicle doors and ignitionswitch for unauthorized entry or operation. When thealarm is activ
TIRE PRESSURE NOW AVAILABLEThe TPMsystem is functioning normally andthe externalinterference is no longer affecting the system.SPARE TIRE IN USE? YES/
CAUTION!The TPM system has been optimized for the originalequipment tires and wheels. TPM system pressureshave been established for the tire size equi
General InformationThis device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•
NOTE: In order to avoid damage to tires, chains, andyour vehicle do not drive for a prolonged period of timeon dry pavement. Observe the tire chain ma
Section of this manual. More frequent rotation is permis-sible if desired. The reasons for any rapid or unusualwear should be corrected prior to rotat
Poor quality gasoline can cause problems such as hardstarting, stalling and hesitations. If you experience thesesymptoms, try another brand of “regula
CAUTION!DO NOT use gasolines containing Methanol. Use ofthese blends may result in starting and driveabilityproblems and may damage critical fuel syst
Sulfur In GasolineYour vehicle may have been designed to meet Californialow emission standards when using cleaner burningCalifornia reformulated gasol
Fuel System CautionsCAUTION!Follow these guidelines to maintain your vehicle’sperformance:•The use of leaded gas is prohibited by Federal law.Using le
•Do not inhale exhaust gases. They contain carbonmonoxide, a colorless and odorless gas which can kill.Never run the engine in a closed area, such as
NOTE:•The driver’s door and liftgate key cylinders cannotarm or disarm the system.•Once the alarm is set, and the liftgate button on thekeyless entry
CAUTION!Damage to the fuel system or emission controlsystem could result from using an improper fueltank filler tube cap (gas cap). A poorly fitting c
WARNING!• Remove the fuel tank filler tube cap (gas cap) slowlyto prevent fuel spray from the filler neck which maycause injury.• The volatility of so
•Vehicle Identification Number (VIN)•Type of Vehicle•Month Day and Hour of Manufacture (MDH)The bar code allows a computer scanner to read theVehicle
Overloading can cause potential safety hazards andshorten useful service life. Heavier axles or suspensioncomponents do not necessarily increase the v
TRAILER TOWINGIn this section you will find safety tips and informationon limits to the type of towing you can reasonably dowith your vehicle. Before
NOTE: Using the “3” range while operating the vehicleunder heavy operating conditions will improve perfor-mance and extend transaxle life by reducing
TRAVEL CONDI-TIONMAXIMUM TRAILER WEIGHT (TRAILER FRONTAL AREA NOT TO EXCEED 32SQ. FT.)3.3L,& 3.8L EN-GINES WITH4-SPEED AUTO-MATIC TRANS-AXLE3.3L &
A load equalizing hitch is recommended for loadedtrailer weights above 1,000 lbs (454 kg) and required forweights above 2,000 lbs (907 kg).CAUTION!If
WHAT TO DO IN EMERGENCIESCONTENTSm Hazard Warning Flasher ...290m If Your Engine Overheats ...291m Jacking And Tire Chang
To keep your door operating properly, observe the fol-lowing guidelines:•Always open the door smoothly.•Avoid high impacts against the door stop when
HAZARD WARNING FLASHERThe hazard flasher switch is located in the center of theinstrument panel above the radio.To engage the Hazard Warning Flashers,
IF YOUR ENGINE OVERHEATSIn any of the following situations, you can reduce thepotential for overheating by taking the appropriate ac-tion.•On the high
WARNING!A hot engine cooling system is dangerous. You orothers could be badly burned by steam or boilingcoolant. You may want to call a service center
Jack LocationThe jack and jack-handle are stowed behind the rear leftside trim panel in the cargo area. Pull up on the lever torelease the cover.Spare
Spare Tire RemovalFit the jack-handle over the drive nut. Rotate the nut tothe leftuntil the spareis on the ground withenough slackcable to allow you
•Turn on the Hazard Warning Flasher.•Block both the front and rearof the wheel diagonally oppo-site the jacking position. Forexample, if changing the
properly engaged in the described location. Do not raisethe vehicle until you are sure the jack is securelyengaged.5. Raise the vehicle by turning the
nuts until each nut has been tightened twice. Correctwheel nut tightness is 130 N·m (95 ft. lbs). If in doubtabout the correct tightness, have them ch
JUMP-STARTING PROCEDURES IF BATTERY ISLOWWARNING!Take care to avoid the radiator cooling fan wheneverthe hood is raised. It can start anytime the igni
1. Wear eye protection and remove any metal jewelrysuch as watch bands or bracelets that might make aninadvertent electrical contact.2. When boost is
INTRODUCTIONCONTENTSm Introduction ...4m How To Use This Manual ...4m Warnings And Cautions ...
NOTE: The driver’s side sliding door cannot be openedwhile the fuel door is open. This feature operates onlywhen the sliding door is fully closed prio
WARNING!Rapid acceleration on slippery surfaces is danger-ous. Unequal traction can cause sudden pulling ofthe front wheels. You could lose control of
WARNING!Fast spinning tires can be dangerous. Forces gener-ated by excessive wheel speeds may cause tire dam-age or failure. A tire could explode and
CAUTION!•Do not attempt to tow this vehicle from the frontwith sling type towing equipment. Damage to thefront fascia will result.•Always use wheel li
TOWING THIS VEHICLE BEHIND ANOTHERVEHICLE WITH A TOW DOLLEYThe manufacture does not recommend that you tow anAll-Wheel Drive (AWD) or front wheel driv
MAINTAINING YOUR VEHICLECONTENTSm 3.3L/3.8L Engines ...308m Onboard Diagnostic System — OBD II ...309m Emissions Inspection An
▫ Steering Shaft Seal ...323▫ Steering Linkage ...323▫ Drive Shaft Universal Joints ...323▫ Body Lubric
▫ Front Fog Light ...349▫ Rear Tail, Stop, Turn Signal, Side Marker AndBack-Up Lights ...350▫ Center High Mount
3.3L/3.8L ENGINES308 MAINTAINING YOUR VEHICLE
ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor
rear seat passengers. Pressing the switch once will openthe power sliding door, once the door is fully openpressing the switch a second time will clos
EMISSIONS INSPECTION AND MAINTENANCEPROGRAMSIn some localities, it may be a legal requirement to passan inspection of your vehicle’s emissions control
ignition key or start the engine. This means that yourvehicle’s OBD system is not ready and you should notproceed to the I/M station.b. The MIL will n
NOTE: Intentional tampering with emissions controlsystems can result in civil penalties being assessedagainst you.WARNING!You can be badly injured wor
Engine OilChecking Oil LevelTo assure proper engine lubrication, the engine oil mustbe maintained at the correct level. Check the oil level atregular
Change Engine OilRoad conditions and your kind of driving affects theinterval at which your oil should be changed. Check thefollowing list to see if a
American Petroleum Institute (API) Engine OilIdentification SymbolThis symbolmeans that the oil hasbeen certified by the AmericanPetroleum Institute (
Synthetic Engine OilsThere are a number of engine oils being promoted aseither synthetic or semi-synthetic. If you chose to usesuch a product, use onl
Belts should be inspected for evidence of cuts, cracks, orglazing, and replaced if there is indication of damagewhich could result in belt failure. If
Engine Fuel FilterAplugged fuel filter can cause stalling, limit the speed atwhich a vehicle can be driven or cause hard starting.Should an excessive
WARNING!A hot exhaust system can start a fire if you park overmaterials that can burn. Such materials might begrass or leaves coming into contact with
•The power sliding door switches will not operate if thevehicle is in gear or the vehicle speed is above 0 mph(0 km/h).•If the power sliding door enco
WARNING!Battery fluid is a corrosive acid solution and canburn or even blind you. Don’t allow battery fluid tocontact your eyes, skin or clothing. Don
Air ConditionerFor best possible performance, your air conditionershould be checked and serviced by an Authorized Dealerat the start of each warm seas
Refrigerant Recovery And RecyclingThe air conditioning system of your vehicle containsR-134a, arefrigerant that doesnot deplete the ozonelayerin the u
If necessary, add fluid to restore to the proper indicatedlevel. With a clean cloth, wipe any spilled fluid from allsurfaces. Refer to Recommended Flu
Body LubricationLocks and all body pivot points, including such items asseat tracks,doors, liftgate, sliding doors andhood hinges,should be lubricated
washer solvent (not radiator antifreeze) and operate thesystem for a few seconds to flush out the residual water.The washer fluid reservoir will hold
WARNING!Exhaust gases can injure or kill. They contain carbonmonoxide (CO) which is colorless and odorless.Breathing it can make you unconscious and c
Coolant ChecksCoolant protection checks should be made every 12months (prior to the onset of freezing weather, whereapplicable). If coolant is dirty o
CAUTION!Mixing of coolants other than specified (non-HOAT), may result in engine damage that may notbe covered under the new vehicle warranty, anddecr
Coolant Pressure CapThe coolant pressure cap must be fully tightened toprevent loss of coolant, and to insure that coolant willreturn to the radiator
When the child lock system is engaged the door can beopened only by using the outside door handle or theswitches located on the trim panel just in fro
operating temperature is satisfactory, the coolant recov-ery bottle need only be checked once a month.When additional coolant is needed to maintain th
•Do not change the thermostat for summer or winteroperation. If replacement is ever necessary, installONLY the correct type thermostat. Other designs
WARNING!Riding the brakes can lead to brake failure andpossibly an accident. Driving with your foot restingor riding on the brake pedal can result in
replaced immediately! Eventual deterioration of the hosecan take place resulting in a possibility of a burst failure.WARNING!Worn brake hoses can burs
WARNING!Overfilling the brake fluid reservoir can result inspilling brake fluid on hot engine parts and thebrake fluid catching fire.Use only brake fl
Automatic TransmissionThe automatic transmission and differential assembly arecontained within a single housing.All automatic transmissions are equipp
Procedure For Checking Fluid LevelThe fluid level in the automatic transmission should bechecked whenever thevehicle is serviced. Operation withan imp
CAUTION!Do not overfill. Dirt and water in the transmissioncan cause serious damage. To prevent dirt and waterfrom entering the transmission after che
Power Transfer UnitThe fluid should be maintained at the bottom of the fillerhole opening. If it becomes necessary to add or replacethe fluid, use onl
Severe Usage is defined as:1. More than 50% of vehicle operation in stop and gotraffic where the vehicle is driven regularly for more than45 minutes o
LIFTGATENOTE: The key that is used to start the vehicle is alsoused to lock or unlock the doors and open the liftgate.To open the liftgate, insert the
•Insects, tree sap and tar.•Salt in the air near seacoast localities.•Atmospheric fallout/industrial pollutants.Washing•Wash your vehicle regularly. A
•If your vehicle is damaged due to an accident orsimilar cause which destroys the paint and protectivecoating have your vehicle repaired as soon as po
and Mopar Total Clean. Care should be taken to avoidsoaking your leather upholstery with any liquid. Pleasedo not use polishes, oils, cleaning fluids,
Seat Belt MaintenanceDo not bleach, dye or clean the belts with chemicalsolvents or abrasive cleaners. This will weaken the fabric.Sun damage will als
dip itback into the water about six times. Thiswill loosenany remaining debris. Rinse the drawer thoroughly un-der warmrunning water. Shakethe excess
CAUTION!•When installing the Integrated Power Modulecover, it is important to ensure the cover is prop-erly positioned and fully latched. Failure to d
air conditioning system at idle for about five minutesin the fresh air and high blower setting. This willinsure adequate system lubrication to minimiz
BULB REPLACEMENTHeadlights1. Remove the three screws securing the headlight mod-ule.2. Turn the bulb socket retaining ring counterclockwise.3. Disconn
CAUTION!Do not touch the new bulb with your fingers. Oilcontamination will severely shorten bulb life. If thebulb comes in contact with an oily surfac
2. Twist the turn signal socket to remove from theheadlight module and pull bulb from socket.3. Replace bulb, reinstall socket and then reinstall theh
NOTE: On vehicles without powerlocks,theliftgatecanonly be opened using the vehicle keys. The key must beheld in the unlocked position for the liftgat
Rear Tail, Stop, Turn Signal, Side Marker andBack-up Lights1. Raise the liftgate.2. Remove the two light assemblypush-in type fasteners.3. Squeeze the
Center High Mounted Stop Light (CHMSL)1. Remove the two screws securing the CHMSL.2. Twist the bulb socket to remove from the CHMSLhousing.3. Pull the
RECOMMENDED FLUIDS, LUBRICANTS ANDGENUINE PARTSEngineComponent Fluids, Lubricants and Genuine PartsEngine Coolant Mopart Antifreeze/Coolant 5 Year/100
ChassisComponent Fluids, Lubricants and Genuine Parts.Automatic Transmission Mopart ATF+4 Automatic Transmission Fluid.AWD Power Transfer Unit Mopart
MAINTENANCE SCHEDULESCONTENTSm Emission Control System Maintenance ...356m Maintenance Schedules ...356▫ Schedule “B” ...
EMISSION CONTROL SYSTEM MAINTENANCEThe “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified toassure t
•Taxi, police, or delivery service (commercial ser-vice).L•Off-road or desert operation.NOTE: Most vehicles are operated under the conditionslisted fo
At Each Oil Change•Change the engine oil filter.•Inspect the exhaust system.•Inspect the brake hoses.•Inspect the CV joints and front suspension compo
SCHEDULE “B”Follow schedule “B” if you usually operate your vehicleunder one or more of the following conditions. Changethe automatic transmission flu
WARNING!During power operation, personal injury or cargodamage may occur. Ensure the liftgate travel path isclear. Make sure the liftgate is closed an
Miles 3, 000 6, 000 9, 000 12, 000 15, 000 18, 000(Kilometers) (5 000 ) (10 000 ) (14 000) (19 000) (24 000) (29 000)Change engine oil and engine oil
Miles 21, 000 24, 000 27, 000 30, 000 33, 000 36, 000(Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000)Change engine oil and engine oi
Miles 39, 000 42, 000 45, 000 48, 000 51, 000 54, 000(Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000)Change engine oil and engine oi
Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000(Kilometers) (91 000) (96 000) (101 000) (106 000) (110 000) (115 000)Change engine oil and engin
Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000(Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000)Change engine oil and eng
Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000(Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000)Change the All Wheel Driv
Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000(Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000)Change engine oil and
Miles 108, 000 111, 000 114, 000 117, 000 120, 000(Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000)Change engine oil and engine oil filte
Inspection and service should also be performed anytimea malfunction is observed or suspected. Retain all re-ceipts.NOTE: The AWD power transfer unit
SCHEDULE “A”Miles 6, 000 12, 000 18, 000 24, 000 30, 000 36, 000(Kilometers) (10 000) (19 000) (29 000) (38 000 ) (48 000) (58 000)[Months] [6] [12] [
•If the power liftgate encounters multiple obstructionswithin the same cycle, the system will automaticallystop and must be opened or closed manually.
Miles 42, 000 48, 000 54, 000 60, 000 66, 000 72, 000(Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) (115 000)[Months] [42] [48] [54] [60]
Miles 78, 000 84, 000 90, 000 96, 000 100, 000(Kilometers) (125 000) (134 000) (144 000) (154 000) (160 000)[Months] [78] [84] [90] [96]Change engine
Miles 102, 000 108, 000 114, 000 120, 000(Kilometers) (163 000) (173 000) (182 000) (192 000)[Months] [102] [108] [114] [120]Change engine oil and eng
Inspection and service should also be performed anytimea malfunction is observed or suspected. Retain all re-ceipts.WARNING!You can be badly injured w
IF YOU NEED CONSUMER ASSISTANCECONTENTSm Suggestions For Obtaining Service ForYour Vehicle ...376▫ Prepare For The Appointment
SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with
The manufacturer has empowered its dealers to makewarranty and repair decisions that ensure you are notinconvenienced. There is no need for you to wai
In Mexico contact:Av. Prolongacion Paseo de la Reforma, 1240Sante Fe C.P. 05109Mexico, D. F.In Mexico (915) 729–1248 or 729–1240Outside Mexico (525) 7
Contract, and you require service after your manufactur-er’s new vehicle limited warranty expires, please refer toyour contract documents, and contact
WINDOWSPower Vent WindowsSwitches on the driver’s door trim panel let the driveroperate the two vent windows from the driver’s seat.Power WindowsYou c
REPORTING SAFETY DEFECTSIn the 50 United States and Washington D.C.: If youbelieve that your vehicle has a defect which could causea crash or cause in
•Service Manuals.These comprehensive service manuals provide theinformation that students and professional techniciansneed in diagnosing/troubleshooti
DEPARTMENT OF TRANSPORTATION UNIFORMTIRE QUALITY GRADESThe following describes the tire grading categories estab-lished by the National highway Traffi
Temperature GradesThe temperature grades are A (highest), B, and C, repre-senting the tire’s resistance to the generation of heat andits ability to di
INDEX10
Adding Fuel ...279Adding Washer Fluid ...232,324Additives, Fuel ...277Adjustable Pedals .
Filter ...337Fluid and Filter Changes ...337Fluid Level Check ...336Interlock System ...
Cargo CompartmentLuggage Carrier ...149Cassette Tape and Player Maintenance ...207Cassette Tape Player ...
Radiator Cap ...329Selection of Coolant ...327,352Cruise Control ...117Cruise Light ...
Auto Down Feature — If EquippedThe driver’s window switch has an auto down feature.Press the window switch past the detent, release, and thewindow wil
Air Cleaner Filter ...317Block Heater ...240Break-In Recommendations ...72Checking Oil Level ...
Fuel ...274Adding ...279Additives ...277Clean Air ...
High Beam/Low Beam Select Switch ...111Lights On Reminder ...109Replacing ...347Time Delay ...
Key-In Reminder ...13Keyless Entry System ...20Keys ...12Knee Bolster ...
Malfunction Indicator ...165Oil Pressure ...165Park ...107,348Passing ...
Mini-Trip Computer ...124Mirrors ...81Automatic Dimming ...82Electric Remote ...
Overheating, Engine ...164,291Owner’s Manual ...4,380Panic Alarm ...22Parking Brake ...
Rear Seat Removal ...93,95Rear Seating Flexibility ...97,99Rear Window Defroster ...233Rear Window F
Untwisting Procedure ...46Seats ...85Adjustment ...85Bench ...
Linkage ...323Power ...249,322Shaft Seal ...323Tilt Column ...
INTRODUCTIONThis manual has been prepared with the assistance ofservice and engineering specialists to acquaint you withthe operation and maintenance
WARNING!In a collision, you and your passengers can suffermuch greater injuries if you are not properly buck-led up. You can strike the interior of yo
Radial ...264Replacement ...266,268Rotation ...273Safety ...
Vanity Mirrors ...84Variance, Compass ...122Vehicle Certification Label ...281Vehicle Identi
WARNING!•It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision,people riding in these areas are more likely
Lap/Shoulder Belt Operating Instructions1. Enter the vehicle and close the door. Sit back andadjust the seat.2. The seat belt latch plate is near the
3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click”.WARNING!•A belt that is buckled into the wrong
4. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap belt portion, pull upon the shoulder belt. To loosenthe lap
6. To release the belt, push the red button on the buckle.The belt will automatically retract to its stowed position.If necessary, slide the latch pla
As a guide, if you are shorter than average, you willprefer a lower position, andif you are taller than average,you’ll prefer a higher position. When
2. At about 6 to 12 inches (15 to 30 cm) above the latchplate, grasp and twist the belt webbing 180° to create afold that begins immediately above the
Center Lap BeltsThe center seating positionshave alap beltonly. To fastenthe lap belt, slide the latch plate into the buckle until youhear a “click”.
NOTE: These devicesare nota substitute for proper seatbelt placementby the occupant. The seat belt still mustbeworn snugly and positioned properly.The
INTRODUCTION 51
Driver and Front Passenger SupplementalRestraint System - AirbagThis vehicle has airbags for both the driver and frontpassenger as a supplement to the
If the vehicle is equipped with side airbags, they arelocated inside the driver and front passenger seatbacks,and their seatcovers are labeled SRS AIR
Airbags inflate in moderate to high speed impacts. Alongwith seat belts and pretensioners, front airbags workwiththe instrument panel knee bolsters to
2. All occupants should wear their lap and shoulderbelts properly.3. The driver and front passenger seats should bemoved back as far as practical to a
The Front Airbag System consists of the following:•Front Airbag Control Module (with integrated sideimpact sensor - if equipped)•AIRBAG Readiness Ligh
The front airbag control module sends amessage to the instrument cluster to turn onthe AIRBAG light in the instrument panelfor 6to 8 seconds when thei
Side Airbags Supplemental Restraint System(SRS) — If EquippedThe Side Airbag System, if equipped, consists of thefollowing:•AIRBAG Readiness Light (sh
If An Airbag Deployment OccursThe airbag systems are designed to deploy when theairbag control modules detect a moderate-to-severe col-lision, to help
WARNING!Deployed airbags and seat belt pretensioners cannotprotect you in another collision. Have the airbagsand seat belt pretensioners replaced by a
Airbag LightYou willwant tohave theairbags ready toinflate foryourprotection in a collision. While the airbag system isdesigned to be maintenance free
WARNINGS AND CAUTIONSThis manual contains WARNINGS against operatingprocedures which could result in an accident or bodilyinjury. It also contains CAU
Children 12 years and under should ride properly buck-led up in a rear seat. According to crash statistics,children are safer when properly restrained
used either rearward-facing or forward-facing in thevehicle. Convertible child seats often have a higherweight limit in the rearward-facing direction
WARNING!•Improper installation can lead to failure of aninfant or child restraint. It could come loose in acollision. The child could be badly injured
•In the rear seat, you may have trouble tightening thelap/shoulder belt on the child restraint because thebuckle or latch plate is too close to the be
Lower Anchors and Tether for CHildren (LATCH)Each vehicle, except commercial cargo vehicles, isequipped with the child restraint anchorage systemcalle
When using the tether anchorages in the outboard seat-ing positions, ensure that the strap is routed over the topof the seatback and under the head re
Fleet vehicles equipped with the LATCH system on the3-passenger bench seat must have the seat adjusted to thefull rear position on the tracks when the
We urge that you carefully follow the directions of themanufacturer when installing your child restraint. Many,but not all, restraint systems will be
•Check belt fit periodically. A child’s squirming orslouching can move the belt out of position.•If the shoulder belt contacts the face or neck, move
WARNING!Rear Facing Infant restraints must never be secured inthe passenger seat of a vehicle with a passengerairbag. In an accident a passenger airba
VEHICLE MODIFICATIONS / ALTERATIONSWARNING!Any modifications or alterations to this vehiclecould seriously affect its roadworthiness and safetyand may
with the seat adjusted to the rear most position. Neverallow children to slide the shoulder belt behind themor under their arm.Tether Installation For
2. Extend the child restraint tether anchor forward to-wards the front passenger seat.3. Follow the child restraint manufacturer’s directionsfor prope
6. Using the hook attached to the child restraint tetherstrap, attach the child restraint tether strap to the metalring on the vehicle tether anchor.7
While cruising, brief full-throttle acceleration, within thelimits of local traffic laws, contributes to a good break-in.Wide open throttle accelerati
WARNING!If you are required to drive with the liftgate open,make sure that all windows are closed, and theclimate control blower switch is set at high
LightsHave someone observe the operation of exterior lightswhile you work the controls. Check turn signal and highbeam indicator lights on the instrum
UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTSm Mirrors ...81▫ Inside Day/Night Mirror ...81▫ Automatic
▫ Manual Reclining Seats — If Equipped ...88▫ Manual Lumbar — If Equipped ...89▫ Middle Quad Fold & Tumble Seating ...90▫ Middle
▫ Front Fog Lights — If Equipped ...110m Multifunction Lever ...110▫ Turn Signals ...110▫ Headlight Lo
m Garage Door Opener — If Equipped ...129▫ Programming Homelink ...130▫ Canadian Programming/Gate Programming . .133▫ Using Homelin
MIRRORSInside Day/Night MirrorAdjust the mirror to center on the view through the rearwindow. A two point pivot system allows for horizontaland vertic
Automatic Dimming Mirror — If equippedIf the switch is in the “Auto” position the mirror willautomatically adjust for annoying headlight glare fromveh
Outside Mirror — Driver’s SideAdjust the outsidemirror to centeron the adjacent lane oftraffic, with a slight overlap of the view obtained on theinsid
Power Remote-Control MirrorsUse the mirror select switch, located on the instrumentpanel to the left of the steering column, to adjust the viewobtaine
SEATSManual Front Seat AdjusterThe adjusting bar is located under the front of the seat.Pull the bar up and move the seat to the desired position.Rele
8–Way Driver’s Power Seat — If EquippedThe driver’s power seat switches are located on theoutboard side of the seat. The front switch controlsup/down,
Adjustable Head Restraints — If EquippedHead restraints can reduce the risk of whiplash injury inthe event of impact from the rear. Pull up or push do
Heated Seats — If EquippedThis feature heats the front driver and passenger seats.The controls for the heated seats are located on theinstrument panel
WARNING!Do not ride with the seatback reclined so that theshoulder belt is no longer resting against your chest.In a collision you could slide under t
THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTSm A Word About Your Keys ...12▫ Ignition Key Removal ...12▫ Key-In-I
Middle Quad Fold & Tumble SeatingThe passenger’s and driver’s side middle quad seats canbe tilted forward for easy access to the third seat or rea
3. Pull up on the seatback release lever located on theoutboard side of the seat and fold the seatback down. Ifthe head restraint contacts the rear of
5. Pull the release bar located at the bottom front edge ofthe seat to disengage the front attachments.6. The seat assembly can now be removed from th
50/50 Fold & Tumble Rear Seat Removal1. Lower the head restraint and pull up on release lever“1” to fold the seatback down.2. Pull up on release l
3. Pull the release strap “3” located at the bottom of theseat to disengage the front attachments.4. The seat assembly can now be removed from thevehi
3 – Passenger Bench SeatsRelease levers are located on the rear leg assemblies, nearthe floor. To remove the seat, squeeze each release handleand rota
Plastic Grocery Bag RetainerRetainer hooks which will hold plastic grocery baghandles are built into the seatbacks of all rear seats andsome front sea
Rear Seat Descriptions7 Passenger Model — 2– passenger bucket seats in thesecond position and 3– passenger bench seat or 50/50bench seat in the third
3. Additional Storage—The 2nd and 3rd row seats installed. The 3rd row benchseat is in the full forward position on the tracks and oneor both of the r
Rear Quad and 50/50 Seating FlexibilityThe seats may be used with either or both seatbacksfolded forward for additional storage space, or witheither o
Commentaires sur ces manuels